Your new favorite room starts here.
Prep Wall
Wallpaper is designed for use on smooth and clean walls. Not for use on brick, textured walls, concrete, or over other wallpaper. Make sure your wall is smooth and free from debris, dirt, mold, mildew, grease, or holes. Then, wipe your wall with a damp cloth and let dry completely.
Proper wall preparation is essential for a successful installation. Be sure to thoroughly wipe down your walls with water to remove any dust or residue, and allow them to dry completely before applying your wallpaper. Even clean-looking walls can have buildup that affects adhesion!
Freshly painted walls need to dry a minimum of 14 days, or until completely cured, before prepping for wallpaper install.
The residual moisture content of walls should be <4%.
For best results we recommend applying wallpaper over walls that have been painted with primer and semi-gloss paint. We recommend ordering a sample and confirming adhesion before ordering.
Remove shelves, wall covering hardware, etc. before starting.
Wallpapering around light switches or outlets? Turn off power to room and remove covers first.
Gather Supplies
- Utility knife or box-cutter knife
- Straight Edge - A metal ruler works wonderfully
- Tape Measure
- A felt edged squeegee
- Level
- A friend to help you!
Lay Out Panels
Allow panels to adjust to the environment by laying them flat in your home (or wherever they will be installed) for a minimum of 24 hours at normal room temperature. Avoid creasing or folding your wallpaper.
Before installation, inspect your wallpaper and confirm the size and color of all panels is correct and that panels are free from damage.
Determine Install Plan
Your wallpaper comes in custom cut panels that will be trimmed during installation.
Each panel will be labeled at the bottom (Panel 1 of 10, Panel 2 of 10, etc). Panel number 1 goes on the left, and the other panels follow to the right in numerical order.
You can install your panels from left to right or right to left.
For wallpaper applications on a single wall, two walls, or three walls: start at the left or right most corner and work your way around until finished.
For full room applications: Choose an inconspicuous starting place, such as behind a door or large piece of furniture. The pattern will likely not line up where the last piece meets the first, so choose a hidden spot to minimize visual disconnect.
Install
Enlist your friend's help to install the wallpaper.
1. Peel away 6” of the backing liner and crease liner (not your printed wallpaper) backwards. Take care to minimize touching the exposed adhesive.
2. Place a few inches of wallpaper (with it’s sticky backing exposed) onto your starting spot on the wall, with about one or two inches of printed wallpaper above the top edge of the wall. This will be trimmed later.
3. Have your friend hold the level and ensure that the wallpaper has been applied level. You can remove the paper and re-stick as necessary. Once the paper is level, press it onto the wall, starting at the center of the panel.
4. Pull the protective backing down another 6 inches, pressing the wallpaper down after. Use your felt squeegee to work out air pockets and bubbles in small segments. Keep the panel flat to the wall and continue to peel off the protective backing in 6 inch sections, repeating the squeegee-ing until you reach the bottom of the panel.
5. Align your next panel by peeling the panel backing down 6 inches and aligning the pattern with the first panel. There should be a 1 inch overlap between panels. Continue removing the backing and squeegee-ing in small sections as you go.
6. Once you've applied all panels, trim the edges off and cut around outlets, light switches, and other openings using a sharp, new utility knife or box cutter blade. Use a straight edge to ensure straight cuts along trim.
Tips:
- Our wallpaper can be repositioned during the installation process. Slowly peel the paper from the wall and reapply if you make a mistake.
- Take your time to ensure the first panel and the top portions of the rest of the panels are installed exactly right. Any misalignment will be amplified by the time you reach the bottom of the wall and is best fixed at the beginning.
- Stubborn bubbles may require you to remove the wallpaper and re-stick. It is important to work in small 6 inch sections to prevent needing to remove a large section later. It is possible to use a needle to pop a large bubble and then squeegee the air out.
- Take care when cutting around outlets and turn off power first.
- Don’t trim away excess paper until you’re finished installing all the panels.
Cleaning
If your wallpaper has a WallBOON finish, it can be cleaned with most household cleaners and a microfiber cloth. We do recommend testing color fastness in a inconspicuous area, first, just in case. Our favorite and recommended cleaner is simply a few drops of Dawn dish soap mixed with water. After cleaning, always wipe clean with water, and dry your wallpaper with a soft, lint-free towel.
If your wallpaper has a Classic finish, clean it with a damp, non-abrasive microfiber cloth. Then dry it with a soft lint-free towel. Avoid rubbing it aggressively and using cleaners.
And just like that, you've got a whole new room. Enjoy!
Questions? Get in touch with our team, we are happy to help.